MCAT06 PROFIBUS DP Active Termination Resistor-PROFIBUS DP Active Termination Resistor-Microcyber Corporation-Fieldbus Instruments ,Gateways,Temperature Transmitter, Pressure Transmitter，Built-in Modules ，WirelessHART ，Built-in Modules，HART Chip Manufacturers

Instruments

Pressure Transmitter
Pressure Transmitter (Capacitance Sensor) Pressure Transmitter (Piezoresistance Silicon Sensor) Pressure Transmitter (Monocrystalline Silicon Sensor)

Temperature Transmitter
Temperature Transmitter (2-channel) Temperature Transmitter (Head Mounted) Temperature Transmitter (8-channel) Temperature Transmitter (Rail Installation)

Current Transmitter
Fieldbus Current Input Transmitter Fieldbus Current Output Transmitter

Module Set
MS Module Set for Temperature

Fieldbus

Conversion Gateway
Modbus to FF Gateway Modbus to PA Gateway Modbus to DP Gateway Modbus to HART Gateway HART to Modbus Gateway HART to FF Gateway

Built-in Modules
Modbus to HART Module Modbus to DP Module Modbus to PA Module Modbus to FF Module MC0310 Modbus to HART Module MC0313 Modbus to FF Module MC0307 Modbus to PA Module MC0312 Modbus to HART-IP Module

Chip
HT1200M HART Communication Controller APC3 DP Communication Controller

Industrial Wireless

Wireless Communication Module

Wireless Development Backplane

Wireless Complete Machine

Wireless Gateway

Testing Service

Accessories

Fieldbus Power & Fieldbus Terminal

Active Fieldbus Distributor

HART Signal Modem

PROFIBUS DP Active Termination Resistor

OEM Service

MCAT06 PROFIBUS DP Active Termination Resistor

MCAT06 is an active termination resistor for PROFIBUS DP and RS-485 networks. With MCAT06, PROFIBUS and other RS-485 2-wire networks can be disconnected directly at the end of the bus. This ensures secure communication even if the bus devices are connected/disconnected during operation.

MCAT06 PROFIBUS DP Active Termination Resistor:
1. Suitable for PROFIBUS DP and other physical layer RS-485 networks
2. Connect the bus using pluggable double-layer spring terminals or Sub-D connectors
3. Active programming and diagnostic equipment can also be powered by Sub-D connectors
4. Standard DIN rail installation

Data download Contact us

Product Description

PROFIBUS DP Active Termination Resistor.png

PROFIBUS DP Active Termination Resistor.jpg

MCAT06 PROFIBUS DP Active Termination Resistor: MCAT06 is an active termination resistor for PROFIBUS DP and RS-485 networks. With MCAT06, PROFIBUS and other RS-485 2-wire networks can be disconnected directly at the end of the bus. This ensures secure communication even if the bus devices are connected/disconnected during operation.

MCAT06 PROFIBUS DP Active Termination Resistor Dimensions:

Dimensional drawing (unit: mm)

MCAT06 PROFIBUS DP Active Termination Resistor Structure Diagram:

DP active terminal machine structure diagram

1	Power supply termina	2	Pad pasting	3	PROFIBUS Programming interface
4	Power light	5	Lower terminal cover plate	6	Bus terminal
7	Terminal dial-up switch	8	Monobloc	9	Upper terminal cover plate

PROFIBUS DP Active Termination Resistor.jpg

MCAT06 PROFIBUS DP Active Termination Resistor Details of Data:

Essential Parameter:

Supply voltage	24 VDC(±20%)
Apply	PROFIBUS DP and RS-485 network PROFIBUS meets IEC 61158 standards, RS-485 and 2 Linear
Working temperature	-20℃～70℃
Storage temperature	-40℃～70℃
Humidity range	5%～95%RH

Performance Index:

Protection grade	The enclosure protection level reaches IP20
Electromagnetic compatibility	Compliance with electromagnetic compatibility requirements for GB/T 18268.1-2010 Measurement, Control and Laboratory Equipment Resistance in Industrial Sites, Part 1: General Requirements

Physical Characteristics:

Weight

0.2kg

Structural material

Monoblock: ABS; Clip:POM;

Coating: polyester epoxy resin.

MCAT06 PROFIBUS DP Active Termination Resistor.jpg