Industrial Communication

G0307 Modbus to Profibus PA converter realizes the converter function from Modbus RTU to PROFIBUS PA, and it shall multiple devices with Modbus RTU protocol to PROFIBUS PA network.

G0307 Modbus to Profibus PA converter：

1. Modbus-RTU protocol to PROFIBUS PA protocol

2. Support PA profile 3.02

3. Support GSD 5.0 specification and standard EDD specification

4. Support AI, AO, DI, DO standard function block

5. Support up to four Modbus devices

Modbus to Profibus DP Converter realizes the conversion function from Modbus RTU to PROFIBUS DP, making multiple slave station devices that conform to Modbus RTU communication regulation access to PROFIBUS DPnetwork. Modbus can be as master or slave, and this function can be realized by a special function button.

G0306 Modbus to Profibus DP Converter：

1. Modbus-RTU protocol to DP protocol

2. Standard DP interface, baud rate self-adapting, support up to 12Mbps

3. Support up to 244 byte input/output

4. Configure Modbus communication parameters by GSD

5. Modbus side can be both master and slave station

G0310 Modbus to HART Converter designed by Microcyber Corporation is a gateway device for Modbus-RTU protocol and HART protocol. As Modbus master, G0310 Modbus to HART Gateway communicates with devices that have Modbus-RTU communication function via RS485 interface. It can convert device data to HART device variables output, and it also supports 4~20mAcurrent output.

G0310 Modbus to HART Converter：

1. Comply with HART 7 protocol

2. Standardization of signal levels for fault messages in digital transmitters according to NE 43

3. Support 1 Modbus slave device

4. Configuring via the HART interface

5. Communication interface support: RS485

6. Standard DIN rail installation

G0313 Modbus to Foundation Fieldbus Converter is a gateway device of Modbus protocol and FF protocol developed by Microcyber. As Modbus master station, G0313 Modbus to Foundation Fieldbus converter communicates with Modbus-RTU device via RS485 interface, and it can convert the data of Modbus-RTU device to Foundation Fieldbus device variable output.

G0313 Modbus to Foundation Fieldbus Converter ：

1. Modbus-RTU protocol to Foundation Fieldbus protocol

2. Comply with Foundation Fieldbus standard

3. Support LinkMaster function

4. Support standard DD specification

5. Support up to four Modbus devices

G1003 HART to Modbus converter realizes the transformation function from HART to Modbus RTU/ASCl, and it can connect multiple HART slavedevices to Modbus network. The HART end of the gateway is the master station, and the Modbus endis the slave station.

G1003 HART to Modbus converter：

1. Comply with HART 7

2. Support HART single point or multipoint mode. Multipoint mode supports connecting up to 15 HART slave devices

3. Support HART custom commands, up to 100, input and output data buffers output data buffers

4. The Modbus end serves as a slave device and supports RTU and ASCll communication modes

5. Communication interface support: RS232, RS485, RS422

6. Standard DIN rail installation

G1013 HART To Foundation Fieldbus converter designed by Microcyber Corporation is a gateway device for HART protocol and FF protocol. As HART master, G1013 HART to FF Gateway communicates with HART slave via HART interface, it can convert dynamic variables in the device to FF device variables output. 

G1013 HART To Foundation Fieldbus converter：

1. Comply with HART 7

2. Supports 4 Als, a total of 16 channels

3. Connect up to 4 HART slave devices

4. The HART interface can power HART slave devices

5. Configuring the gateway via the FOUNDATION FIELDBUS interface

6. Standard DlN rail installation

M0310 Modbus to HART embedded module is one of the Microcyber M series embedded modules developed by Microcyber Corporation. By embedding M0310 into the user device with Modbus RTU communication capability, the Modbus slave can be transformed into a HART slave.

M0310 Modbus to HART embedded Module：

1. Comply with HART V7.0 protocol standard 

2. Comply with standard Modbus RTU protocol

3. Support Modbus communication parameters dynamic configuration

4. Support 6 device variables and 4 dynamic variables

5. M0310-ACT is an actuator-specific version and different from M0310 hardware

M0306 Modbus to Dp built-in module is one of the Microcyber Mseries embedded modulesdeveloped by Microcyber Corporation. This series of embedded modules have features like same sizesame interface, easy to upgrade, easy configuration and so on, it is the ideal choice for users to quicklydevelop the fieldbus equipment.

M0306 Modbus to Profibus DP embedded module:

1. Support 1 Modbus RTU slave device

2. Comply with PROFIBUS-DP/V0 protocol

3. Modbus RTU and PROFlBUS DP protocols are flexibly configurable via GsD files

4. Suitable for frequency converters with Modbus protocol interface,motor starting protection devices, various transmitters, intelligent field measurement equipment and instruments, etc

5. Supply voltage: 3.3V or 5V available

M0307 Modbus to Profibus PA embedded module is one of the Microcyber M-series built-in modules developed by Microcyber Corporation. By embedding the M0307 into the users’ device with Modbus-RTU communication capabilities, the user device can be changed to Profibus PA slave station. 

M0307 Modbus to Profibus PA embedded module：

1. Comply with PA 3.02 specification

2. Support Modbus communication parameters dynamic configuration

3. Support function block AI, AO, DI, DO, PID, etc.

4. Support up to 4 channels AI, AO, DI, DO